2018 Ford Expedition Radio Not Working: Fix It Now!

Do you own a 2018 Ford Expedition and are experiencing problems with the radio If so, you are not alone. This is a common issue that can be frustrating and inconvenient. But don’t worry, there is a fix! In this guide, I will walk you through the steps to troubleshoot and repair your 2018 Ford Expedition radio. By the end of this guide, you will have your radio up and running again in no time.

Reasons Why 2018 Ford Expedition Radio Not Working

Here are the reasons:

No power to the radio

– The radio fuse is blown.
– The radio wiring harness is damaged.
– The radio antenna is not connected properly.
– The radio is not receiving power from the vehicle’s computer.

The radio is stuck in Safe Mode

– The radio was turned off while the battery was disconnected.
– The radio was turned off while the vehicle was in ACC or ON mode.
– The radio was reset using the radio’s reset button.

The radio is not programmed properly

– The radio was not programmed when the vehicle was new.
– The radio was reprogrammed using the wrong software.
– The radio’s programming was corrupted.

The radio is defective

– The radio is damaged due to water or moisture damage.
– The radio is damaged due to a power surge.
– The radio is damaged due to a manufacturing defect.

How to Troubleshoot: 2018 Ford Expedition Radio Not Working

Your 2018 Ford Expedition’s radio is an important part of your driving experience. It provides you with entertainment, navigation, and communication while you’re on the road. If your radio isn’t working, it can be a major inconvenience.

There are a few different things that could be causing your radio to not work. In this article, we’ll walk you through the steps to troubleshoot the problem and get your radio back up and running.

Step 1: Check the fuses

The first thing you should do is check the fuses in your Expedition’s radio. To do this, you’ll need to find the fuse box. The fuse box is usually located under the hood, on the driver’s side.

Once you’ve found the fuse box, locate the fuse for the radio. The fuse for the radio is usually labeled Radio or AM/FM.

Check the fuse to make sure it’s not blown. If the fuse is blown, you’ll need to replace it with a new fuse.

Step 2: Check the connections

The next thing you should do is check the connections to the radio. The radio is connected to the car’s electrical system by a series of wires. These wires can become loose or damaged over time, which can cause the radio to stop working.

To check the connections, you’ll need to remove the radio from the dashboard. Once you’ve removed the radio, you can check the connections to make sure they’re tight and secure.

If the connections are loose or damaged, you’ll need to reconnect them or repair them as needed.

Step 3: Reset the radio

If the fuses and connections are okay, the next thing you can try is resetting the radio. To reset the radio, you’ll need to find the reset button. The reset button is usually located on the back of the radio.

Press the reset button and hold it for a few seconds. This will reset the radio to its factory settings.

Step 4: Take your Expedition to a dealership

If you’ve tried all of the steps above and your radio is still not working, you’ll need to take your Expedition to a dealership. The dealership will be able to diagnose the problem and fix it for you.

Conclusion

Your 2018 Ford Expedition’s radio is an important part of your driving experience. If your radio isn’t working, it can be a major inconvenience.

By following the steps in this article, you can troubleshoot the problem and get your radio back up and running. However, if you’re unable to fix the problem yourself, you’ll need to take your Expedition to a dealership.

Also Read: 2018 Ford Expedition Screen Not Working

FAQs: 2018 Ford Expedition Radio Not Working

Why is my 2018 Ford Expedition radio not working?

There are a few possible reasons why your 2018 Ford Expedition radio may not be working. Here are a few of the most common:

The radio is not turned on: Make sure that the radio is turned on and that the volume is not turned down too low.

The radio is not receiving a signal: Check to make sure that the radio is tuned to a valid station. If you are in an area with poor reception, you may need to move to a different location in order to get a better signal.

The radio is damaged: If the radio has been damaged, it may need to be repaired or replaced.

How do I turn on my 2018 Ford Expedition radio?

To turn on the radio, press the power button. The power button is located at the top of the radio.

How do I tune the radio in my 2018 Ford Expedition?

To tune the radio, use the tuning knob. The tuning knob is located on the right side of the radio. Turn the tuning knob clockwise to increase the frequency or counterclockwise to decrease the frequency.

How do I change the source on my 2018 Ford Expedition radio?

To change the source, press the source button. The source button is located at the bottom of the radio. Each press of the source button will cycle through the available sources.

How do I troubleshoot my 2018 Ford Expedition radio?

If your 2018 Ford Expedition radio is not working, there are a few things you can do to troubleshoot the problem. Here are a few tips:

Check the fuses: Make sure that the fuses for the radio are not blown.

Reset the radio: Press and hold the power button for 10 seconds to reset the radio.

Update the software: Check to see if there is a software update available for the radio. If there is, update the software and see if the problem is resolved.

Take the vehicle to a dealership: If you have tried all of the above and the problem persists, you may need to take the vehicle to a dealership for further diagnosis and repair.